Author: Ale Moglia

"A mistake is always forgivable, rarely excusable and always unacceptable. " (Robert Fripp)

HY1269 curves

HY1269 I’m a big fan of the thoriated-tungsten filaments and I value them not just because they do look very cool, but fundamentally due to how they sound in a single-ended stage. I hope to build a nice push-pull amp with these type of valves soon.

I found a pair of HY1269 valves recently. This valve is not well-known amongst the used ones out there but they do have some interesting characteristics as a directly heated tetrode that would be interesting to consider it for a plate-to-grid (Schade) feedback configuration.  With its 30W of anode dissipation capability, it’s a good candidate for an output stage. However, it’s quite likely that you will have to drive it in A2 to get the most out of this valve. Like designs using 811a and similar transmitting valves, the HY1269 can be operated in class A2 even with no signal on the grid.

As per my “Robustiano” design using the 6P21S, it would be nice to see extracting 6W or more out of this  transmitting valve. I’m sure that the thoriated-tungsten touch will provide a lovely sound if properly implemented.

Continue reading “HY1269 curves”

Starlight Discrete DAC Festival – London 2014

Jon’s ESL 6C4C drivers
Oh, are you taking a picture?
Bipolar discrete DAC ready
Final adjustments to the bipolar DAC guinea pig!
It never goes as planned
One hand is never enough
Jonathan’s Ti48 + DAC

A lot was already said about this fantastic day at Jon’s. The Starlight CD + Discrete DAC festival didn’t go as planned but we had a wonderful time. I had the chance to bring my own Starlight and sounded nice in Jon’s system despite the ground loop issue. Not clear what it was, despite it played well at low AVC levels but not when volume was increased. Perhaps was the load? Anyway, lots of tests from differential DACs to cathode follower outputs and Tom’s bipolar version.

I have to admit that the transformer coupled DAC sounded very transparent and detailed. The valve output gave a warmer tone and even harmonic contribution. The 6N1P implemented as cathode follower was very well received.

Tom’s bipolar DAC implementation is very promising. Clearly the tiny DC bias saturated the AVC and bass wasn’t good. Once we added the coupling PIO it came back to life with a subtle sound I enjoyed very much. Some challenges aside with the ESL resonances which I hope Jon can sort out soon.

Food and hospitality were superb in another unusual warm September day.

Most of all, a great day with fantastic company.

Thank you all

Ale

 

 

6P21S tetrode curves and model

6P21STime ago I generated the tetrode curves for this great directly heated tetrode using my analog curve tracer. I originally used this tetrode in triode-mode. Although it’s a good candidate for a SET amplifier with its 21W in triode-mode, I always wanted to find out how it will perform with Schade-type anode to grid feedback. Building an accurate beam-type tetrode model was key. Luckily now, Derk Reefman has developed an accurate model for these type of valves.

I also worked with Ronald Dekker and insisted him to build in the “Schade” feedback capability in the uTracer using software rather than hardware:

Continue reading “6P21S tetrode curves and model”

Starlight CD transport and discrete DAC finished!

 

After an incredibly long journey I’m glad to say that is nearly over. The Starlight CD transport (I2S output and 4x oversampling) with its discrete DAC sounds absolutely amazing. Getting back to play my CDs is what I was cherishing for a long time. I will be bringing my +500 CD collection from my previous home soon so that would be perfect timing.

I promise to write up a proper blog entry with a full description of the learning experience. For now, I will just sit down and relax. Listen to many CDs and enjoy!

All the acknowledgements and thanks go to Tom Browne for this fantastic design and all the help provided throughout this journey. I think this is the Starlight number 20 or so built so far. Not sure if there are other ones being built anyway.  Also my thanks go to Jon Finlayson for his help on the DAC boards, Richard for the UI stuff and to Tony for inspiring me to give it a go…

IMG_0040.JPG

IMG_0041.JPG

4P1L with screen as anode

A friend in DIYAudio came up with a great idea of using the 4P1L in a different way for a pre-amp/line stage. Given availability of IT and its gapped current, he suggested connecting the 4P1L differently. Instead of using the anode as the anode element, the screen is used as anode. The 4P1L screen has a maximum current of 10mA and dissipation should be within the 1.5W.

The 4P1L curves in this mode

Let’s look at an initial transfer curve with Uak=100V:

4P1L Screen as Anode transfer

 

 

 

 

 

 

 

 

I wired the 4P1L in the following way to allow tracing with the uTracer:

4P1L screen as anode connectionThe connection is slightly different as the one suggested by Indra. If you are looking to implement filament bias, you will have to rearrange the anode and suppressor grid connection and expect a slight shift on the curves given the change in bias. Filaments are in series here, however is preferred to wire them in parallel when using this valve in filament bias as a smaller filament resistor will be required given there is twice the filament current when filaments are connected in parallel. This will help to keep the output resistance lower as the size of this resistor is smaller (remember it is reflected multiplied by μ+1 times.

Continue reading “4P1L with screen as anode”