01a Low Gain DHT preamp

How many times I’ve been asked “how do I lower the gain of the DHT preamp?” many builders love the DHT sound and yet don’t really need that gain. Of course when you use a transformer load, step down is the obvious choice. And it works really well when you invest in a very good quality OPT.

However, when you use DHT with high rp, generally most of the low current ones, you face a tough challenge with regard to frequency response.

With the hybrid mu-follower topology (aka gyrator) we have the problem that the gain is fixed to nearly mu.

I’m in love with the DHT sound and in a preamp a 01a and the 801a/VT-25 DHT Preamp Update preamp cannot be beaten in my view. They all deliver a gain of 8 with a hybrid mu-follower topology.

This can be overcome in the following way: Continue reading “01a Low Gain DHT preamp”

300B SE Amp: build part VII (D3a driver)

It didn’t take long (or at least as long as I thought it would) to finish the driver board. It has a D3a hybrid mu-follower with SiC cathode bias arrangement:

D3a Driver Board Finished

The board is mounted on top of this previous board.

Continue reading “300B SE Amp: build part VII (D3a driver)”

E282F HP Amp

First and foremost, Merry Christmas! I hope you’re having a great time with your loved ones and good music.

Without a mood for public introspection this time, I have to say that I will celebrate this holiday the best I can. I will be hosting today with a lot of meat, wine and single malt. What else can I do? When I escape from the little ones, will get back to spin some records and hopefully work on the projects.

Merry Christmas to everyone

Headphone Amp Quest Continues

Obviously, I needed to pursue this project further. I’ve been lately listening a lot to HPs as simply is the best choice for me when the young family is in bed. In addition to this, I find the HP setup to force me to connect a bit more to what I’m listening to as I don’t get easily distracted.

Continue reading “E282F HP Amp”

6e6p-dr Headphone Amp – part 3

6e6p-dr HP amp in action – cap coupled output

I’ve been running with this HP amplifier for a few weeks now and I have to say I’m delighted with it. I matched a pair of 6e6p-dr on my eTracer and after fiddling with the operating point a bit, I settled for Ia=25mA and Va=180V. Anode voltage will depend on the valve as said before, the Russian valve parameters tend to be all over the place. Anyhow, expect anode voltage to be around 170 to 185V. The beauty of the gyrator PCB is that you can adjust the anode voltage with the trimpot.

Continue reading “6e6p-dr Headphone Amp – part 3”

VT-25/801a/10Y DHT Preamp with SiC filament bias

For quite some time now I wanted to share one of the variations of the famous VT-25/10Y pre-amplifier. As usual due to work, business travel and family duties, I’ve struggled to find the time to update the blog.

Continue reading “VT-25/801a/10Y DHT Preamp with SiC filament bias”

300B Amps: an early breadboard

Browsing my schematic archive I found this early implementation from some years ago on the 300B:

The amp design is straight forward. Let’s start from the output stage. The 300B is run hot at 33W (376V/90mA) with a fixed bias of about -78V. I used a pair of LL1623/90mA OPTs which I had wired on 3K:8 mode.

Continue reading “300B Amps: an early breadboard”

Ba DHT Preamp Build

Just in the last days before the arrival of our second child, I had a spot of luck and managed to get some free time to work on my DHT preamp experiments. 

A pair of NOS Siemens “Ba” valves under initial testing 

Originally I was put off by the hum pickup susceptibility of the Ba German DHT. However, I decided it was time to listen to the design I worked and experimented in my workshop time ago. I remember listening to this valve and was very pleased with its sound. 

Continue reading “Ba DHT Preamp Build”

ER801a Driver Stage

ER801a as Driver in my system

Received the ER801a today back from Thomas. They were working fine, it was a faulty UX-4 socket pin of my tracer which annoyingly made the grid to appear faulty and open at certain voltage level. I need to replace it.

Either way, they are now in my system and I can only say how much I was surprised with the sound of these. They take the detail and timbre of the VT-25 to a next level. Amazing result, happy to have these as part of my driver stage. The preamp is the 201a feeding the ER801a into the 4P1L PSE

Highly recommended valves, worth the price indeed.

DHT Audio Shootout @ London

Here’s the summary of the shootout day we had yesterday at my place with  Tony Rees and Andy Evans

Test Music

For testing the pre-amps Andy suggested the following 2 tracks:

  1.  Ravel Feria (Cleveland/Boulez)
  2. Janacek The Cunning Little Vixen Act 3 Scene 7 “A vixen’s running through the woods” Prague Theatre/Gregor


The Ravel is orchestrated for a large orchestra and percussion, and listening was particularly for the timbre of strings, brass and woodwind and the clarity of the percussion. The Janacek is for several different voices and chorus, and listening was for the tone and character of the voices and how well they were differentiated from each other. In both cases the overall clarity, life and crispness was considered.

Andy Evans

Although I wasn’t familiarised enough with these 2 tracks myself, I found them to be an excellent choice and a reflection of Andy’s musical experience and knowledge as musician. 

Continue reading “DHT Audio Shootout @ London”

SiC cathode bias

Playing this afternoon with the SiC C3D02060F, which can happily run +20mA with very low dynamic resistance. Ideal for the 6e5p/6e6p driver I had in mind for the 300B amp:

C3D02060F-1At 20mA of cathode current the forward voltage is 0.85V and dynamic resistance 1.5Ω. If cathode current is 40mA instead the resistance drops down to 1Ω:

C3D02060F-2The 6e5P/6e6P will run comfortably around 30-40mA and bias tends to be around 3.5-3.7V to swing nice volts as needed. Therefore, we will need 4 SiC in series. 4Ω resistance is good enough and not adding much when reflected to the anode…